Join Now

Bevelling not working on Back Slots

Forum Archive › Bevelling not working on Back Slots

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • December 29, 2022 at 3:50 pm #15797
    RICHARD BROWN
    Participant

      Trying to bevel the back slots only works with Ctrl + B, not with the modifier please help!

      December 30, 2022 at 3:55 am #76949
      Adrian Bellworthy
      Participant

        Its probably because of the face angle. You may need to make the slots a little deeper or change the angle on the modifier.
        Can you share a screen shot of the back slots area?

        December 30, 2022 at 7:27 am #76950
        Omar Domenech
        Participant

          And the remember the usual suspects. Be sure to have your scale applied. Be sure to remove double vertices. Be sure you have consistent normals. Check for overlapping faces and such.

          December 30, 2022 at 9:50 am #76951
          RICHARD BROWN
          Participant

            I’ve inserted a link to the video to display the difficulty I am having, thank you for your time.

            December 30, 2022 at 9:52 am #76952
            RICHARD BROWN
            Participant

              However, how would I be able to remove double faces?

              December 30, 2022 at 9:53 am #76953
              Adrian Bellworthy
              Participant

                In edit mode, press A to select all verts, press M and select by distance.

                December 30, 2022 at 10:13 am #76954
                Omar Domenech
                Participant

                  I can’t see the link anywhere. Did you post it here or somewhere else?

                  December 30, 2022 at 11:23 am #76955
                  RICHARD BROWN
                  Participant

                    https://www.dropbox.com/s/x79m453kmryu0al/Desktop%202022.12.29%20-%2015.41.09.01.mp4?dl=0

                    Not sure why it didn’t post

                    December 31, 2022 at 12:39 pm #76956
                    RICHARD BROWN
                    Participant

                      Link is above to be inspected at your earliest convenience.

                      January 1, 2023 at 1:28 pm #76957
                      Omar Domenech
                      Participant

                        One of the things that could be happening is your object scale. Be sure you applied the scale of your object. After that, try adjusting your bevel amount. In the video you have it set to 30.1 cm, so that may be too small or perhaps too big, depending on the scale of your object. That’s why it’s important to model to scale or not have the scale values out of whack. If you’re still having trouble, you can share a link with your file so we can help do some troubleshooting. 

                        January 3, 2023 at 5:21 am #76958
                        Adrian Bellworthy
                        Participant

                          You may have double verts. On the Bevel Modifier, Clamp Overlap is enabled. This stops the bevel from overlapping the next verts along the edges. Uncheck this and try again. If it now bevels but gives a horrible looking mesh overlap, undo the bevel (CTRL+Z), Press A to select all, Press M and select ByDistance, This will remove any double verts. 
                          Re-enable Clamp Overlap and try the Bevel again.

                          February 18, 2023 at 12:09 pm #76959
                          Christopher Schmidt
                          Participant

                            I also had problems getting those bevels to work. Turning off “Clamp Overlap” in the Bevel Modifier solved it.

                          • Author
                            Posts
                          Viewing 12 posts - 1 through 12 (of 12 total)
                          • The topic ‘Bevelling not working on Back Slots’ is closed to new replies.